AllWeather Conduit Box
The EG4 AllWeather Conduit Box is the outdoor-rated conduit box for the EG4 inverter family. It mounts to the bottom of a wall-mounted EG4 inverter (12000XP, 18kPV, 12kPV, FlexBOSS18, or FlexBOSS21 depending on the build) and provides the conduit landings and DC/AC wiring space the inverter needs.
In stock and ready to ship.
- Type
- Outdoor-rated conduit box
- Mounting
- Below wall-mounted EG4 inverter
- Enclosure
- NEMA 3R outdoor
- Knockouts
- Pre-cut for DC, AC, and PV conduit runs
- Pairs with
- 12000XP Top Plate (optional)
- Compatible inverters
- EG4 12000XP, 18kPV, 12kPV, FlexBOSS18, FlexBOSS21
About this item
The EG4 AllWeather Conduit Box is the outdoor-rated conduit box for the EG4 inverter family. It mounts to the bottom of a wall-mounted EG4 inverter (12000XP, 18kPV, 12kPV, FlexBOSS18, or FlexBOSS21 depending on the build) and provides the conduit landings and DC/AC wiring space the inverter needs.
NEMA 3R rated, which means it can sit outside without a separate roof or rain shield. Pre-cut knockouts in the bottom and sides for the conduit runs to the panel, the battery, and the PV combiner. Internal wire management keeps the lugs accessible during install and inspection.
The Buildable Conduit Box is the indoor or sheltered alternative if your inverter sits in a garage or utility room. The AllWeather is the right pick when the inverter is on an exterior wall or under a carport. Pairs with the 12000XP Top Plate when the install wants the top plate finish.
More Racking & Mounting
Buildable Conduit Box
The EG4 Buildable Conduit Box is the modular conduit box that mounts under an EG4 inverter for the DC and AC landings. It's the indoor or sheltered version of the AllWeather, designed for a garage, utility room, or sheltered exterior wall where the install doesn't need a NEMA 3R rating. The "buildable" name comes from the customer-configurable knockouts. You knock the ones you need for your specific conduit run pattern and leave the rest closed, so the same box works for grid-tied builds, off-grid builds, and battery-attached builds without a separate SKU. Pairs with the 12000XP, 18kPV, 12kPV, FlexBOSS18, and FlexBOSS21. Step up to the EG4 AllWeather Conduit Box when the inverter mounts on a fully exposed exterior wall.
$100
End Clamp
The UFO-END is the end clamp for the IronRidge XR rail system. It sits at the outside edge of each row where the last module needs to be locked down without a second module pressing against it. Two per row, one at each end. Drop the clamp into the XR rail T-slot, set the end module against it, torque to spec. It bonds the module frame to the rail electrically as part of the IronRidge Integrated Grounding System, so you don't need a separate grounding lug at the row ends. Pair with UFO mid clamps along the rest of the row. The two together cover every module-to-rail attachment in a standard residential install. UL 2703 listed. 25-year IronRidge warranty.
$5.28
IntegraRack BallastRack Frame IR-30
The IR-30 is a single fixed-tilt ground rack at 30 degrees. One frame holds one module (standard residential up to oversized 800W panels). It's 6061-T6 aluminum, ships in a 5"x5"x48" box at about 10 pounds, and the structural assembly goes together in under 2 minutes. The 30-degree tilt hits a year-round sweet spot for most of the lower 48: enough angle to shed snow in winter, not so much you lose summer production. The module slides up and down the frame for ground clearance, so you can clear tall grass, brush, or sand drift without redesigning the rack. You can anchor it four ways: EarthBallast pans (concrete blocks set on the soil), AnchorSpike for soft ground, drilled concrete anchors for slab, or IntegraRack EarthScrews for dense compacted soil. The EarthScrews are the fastest of the four on most sites; we stock those too. Engineered for 150 mph wind and 100 psf snow at the design level. UL 2703 listed for mechanical and bonding. Pairs with most standard solar modules without special hardware kits.
$125